Optimasi Multi Respon pada Proses Gurdi dengan Menggunakan Metode Taguchi–Grey

Authors

  • Yopi Y. Tanoto Jurusan Teknik Mesin, Fakultas Teknologi Industri, Institut Teknologi Sepuluh Nopember, Surabaya Kampus ITS, Keputih, Sukolilo – Surabaya 60111 Program Studi Teknik Mesin, Fakultas Teknologi Industri, Universitas Kristen Petra, Jalan Siwalankerto 121-131, Surabaya 60236
  • Bobby O. Soepangkat Jurusan Teknik Mesin, Fakultas Teknologi Industri, Institut Teknologi Sepuluh Nopember, Surabaya Kampus ITS, Keputih, Sukolilo – Surabaya 60111
  • Arief Wahjudi Jurusan Teknik Mesin, Fakultas Teknologi Industri, Institut Teknologi Sepuluh Nopember, Surabaya Kampus ITS, Keputih, Sukolilo – Surabaya 60111

Keywords:

Grey relational analysis (GRA), drilling, Taguchi.

Abstract

Holes making is among the most important operations in manufacturing, and drilling is a major and common hole-making process. In this study, drilling parameters namely cutting speed, feed and point angle as drilling parameters. Each parameter has three levels. This paper is conducted for getting the best parameter setting for minimizing thrust force, torque, surface roughness and flank wear during drilling process. Drilling tests are carried out using high speed steel (HSS). Taguchi’s L9 (33) orthogonal array is used to perform drilling of S50C steel plates. Then, combination between grey relational analysis (GRA) and Taguchi’s method is used for optimizing experiment result (multi response).Experiment result show the contribution of factors in minimizing variation of multiple response, i.e., feed (61.44%), point angle (36.62%) and cutting speed (1.22%). From an optimization result that has validated in confirmation experiment, optimal response is set at 29,94 m/min for cutting speed, 0,07 mm/rev for feed and 134º for point angle.

References

Kalpakjian, S. and Schmid, S.R., Manufacturing Engineering and Technology, Sixth Edition, Pearson, New York, 2009.

Soejanto, I., Desain Eksperimen dengan Metode Taguchi, Graha Ilmu, Yogyakarta, 2009.

Haq, A.N., Marimuthu, P., dan Jeyapaul, R., Multi Respon Optimization of Machining Parameters of Drilling Al/SiC Metal Matrix Composite using Grey Relational Analysis in the Taguchi Method, International Journal Advance Manufacture Technology, 37, 2009, pp. 250–255.

Khrisnamoorthy, A., Boopathy, S., Palanikumar, K., and Davim, J., Aplication of Grey Fuzzy Logic for the Optimization of Drilling Parameters for CRP Composites with Multiple Performance Characteristic, Measurement, 45, 2012, pp. 1286–1296.

Datta, S. and Mahapatra, S.S., Modeling, Simulation and Parametric Optimization of Wire EDM Process using Response Surface Methodology Coupled with Grey-Taguchi Technique, International Journal of Engineering, Science and Technology, 2(5), 2010, pp. 162-183.

Huang, J.T. and Liao, Y.S., Optimization of Machining Parameters of Wire-EDM based on Grey Relational and Statistical Analyses, International Journal of Production Research, 41, 2003, pp. 1707–1720.

Tosun, N., Cogun, C., and Tosun, G., A Study on Kerf and Material Removal Rate in Wire Electrical Discharge Machining based on Taguchi Method, Journal of Materials Processing Technology, 152, 2004, pp. 316-322.

Ross, P.J., Taguchi Techniques for Quality Engineering, McGraw Hill Companies, Inc., Taiwan, 2008.

Lin, J.L. and Lin, C.L., The Use of Orthogonal Array with Grey Relational Analysis to Optimize the Electrical Discharge Machining Process with Multiple Performance Characteristics, International Journal of Machine Tools and Manufacture, 42, 2002, pp. 237–244.

Downloads

Published

2014-05-01

Issue

Section

Articles