Rancang Bangun Drill Jig untuk Pembuatan Lubang Locator
DOI:
https://doi.org/10.9744/jtm.23.2.122-134Keywords:
drill jig, locator, jig and fixture, manufacturing process, CAEAbstract
Advances in manufacturing technology require accurate, consistent, and efficient drilling processes. Manual drilling of locator holes can cause positional deviations and rely on operator skill. This study aims to design, fabricate, and evaluate a drill jig to produce locator holes with diameters of 6, 8, and 10 mm while accommodating variations in workpiece position and thickness. The research stages included requirement identification, CAD-based design, drilling and clamping force calculations, CAE-based structural analysis, prototype fabrication, and experimental testing. The main structure was made of SS400 steel. Simulation results showed a maximum von Mises stress of 213.32 MPa, maximum displacement of 0.0691 mm, and minimum safety factor of 0.97. Experimental testing was conducted in five trials using a bench drill on an 18-mm-thick SS400 workpiece with a nominal hole diameter of Ø8 mm. Using the drill jig reduced average loading time from 43.20 s to 29.80 s, unloading time from 31.80 s to 22.00 s, and drilling time from 39.40 s to 31.00 s. Average cycle time decreased from 114.40 s to 82.80 s, representing a 27.6% reduction. The average hole diameter with the drill jig was 8.05 mm, closer to the nominal diameter than the 8.20 mm obtained without the jig.
References
F. Fiedler et al., “Jigs and Fixtures in Production: A Systematic Literature Review,” Journal of Manufacturing System, vol. 72, pp. 373–405, 2024, https://doi.org/10.1016/j.jmsy.2023.10.006.
H. C. Möhring, D. Biermann, F. Bleicher, S. Melkote, and G. Kappmeyer, “Fixtures and workpiece clamping systems in machining,” CIRP Annals, vol. 74, no. 2, pp. 945–969, 2025, doi: https://doi.org/10.1016/j.cirp.2025.04.096.
H. Liu, C. Wang, T. Li, Q. Bo, K. Liu, and Y. Wang, “Fixturing technology and system for thin-walled parts machining: a review,” Frontiers of Mechanical Engineering, vol. 17, no. 4, Article 55, 2023, doi: 10.1007/s11465-022-0711-5.
C. Liu, J. Wang, B. Zhou, J. Yu, Y. Zheng, and J. Liu, “Development of Fixture Layout Optimization for Thin-Walled Parts: A Review,” Chinese Journal of Mechanical Engineering, vol. 37, no. 1, Article 17, 2024, doi: 10.1186/s10033-024-01004-w.
J. A. M. Peer and R. Journal, “A Review on Jig Manufacturing Techniques,” JournalNX, vol. 10, no. 11, pp. 43–48, 2024.
A. Faizin, H. Wicaksono, and N. P. Sari, “Design and Analysis of Pneumatic Drilling Fixture Using A Microcontroller-Based Control System BT ", Proceedings of the 2022 Annual Technology, Applied Science and Engineering Conference (ATASEC 2022),” Malang, Indonesia, 2022, doi: 10.2991/978-94-6463-106-7_16.
D. Wu, H. Wang, L. Huang, and Y. Wang, “Computer Aided Machining Fixture Design Algorithm and Software Based on Case Learning for Near-Net-Shaped Jet Engine Blade,” Journal of Manufacturing Processes, vol. 69, pp. 545–555, 2021, doi: https://doi.org/10.1016/j.jmapro.2021.07.057.
H. Wang, K. Zhang, D. Wu, T. Yu, J. Yu, and Y. Liao, “Analysis and Optimization of The Machining Fixture System Stiffness for Near-Net-Shaped Aero-Engine Blade,” International Journal of Advanced Manufacturing Technology, vol. 113, no. 11, pp. 3509–3523, 2021, doi: 10.1007/s00170-021-06730-2.
S. U. Butt, M. Arshad, A. A. Baqai, H. A. Saeed, N. A. Din, and R. A. Khan, “Locator Placement Optimization for Minimum Part Positioning Error During Machining Operation Using Genetic Algorithm,” International Journal of Precision Engineering and Manufacturing, vol. 22, no. 5, pp. 813–829, 2021, doi: 10.1007/s12541-021-00500-6.
Q. Feng, W. Maier, T. Stehle, and H. C. Möhring, “Optimization of A Clamping Concept Based on Machine Learning,” Production Engineering, vol. 16, no. 1, pp. 9–22, 2022, doi: 10.1007/s11740-021-01073-z.
M. R. C. Qazani, H. Parvaz, and S. Pedrammehr, “Optimization of Fixture Locating Layout Design Using Comprehensive Optimized Machine Learning,” International Journal of Advanced Manufacturing Technology, vol. 122, no. 5, pp. 2701–2717, 2022, doi: 10.1007/s00170-022-10061-1.
N. A. Said et al., “Design and Fabrication of Jig and Fixture for Drilling Machine in the Manufacturing Industry to Improve Time Productivity,” Journal of Advanced Research in Applied Sciences and Engineering Technology, vol. 29, no. 2 SE-Articles, pp. 304–313, 2023, doi: 10.37934/araset.29.2.304313.
G. Ding, Y. Wang, S. Yuan, L. Lin, and Z. Zhao, “Research on Rapid and Accurate Fixture Design for Non-Intervention Machining of Complex Parts,” Metals 2022, vol. 12, no. 7, Article 11742022, doi: 10.3390/met12071174.
V. Ivanov et al., “Development of Flexible Fixtures with Incomplete Locating: Connecting Rods Machining Case Study,” vol. 10, no. 7, Article 493, 2022. doi: 10.3390/machines10070493.
S. Subramanian, A. K M, and P. Praveen, “Optimization of Machining Fixture Layout for Thin Walled Component using DoE and FEM,” Journal of Applied Research and Technology, vol. 21, no. 4, pp. 552–559, Aug. 2023, doi: 10.22201/icat.24486736e.2023.21.4.1398.
S. A. Haseeb et al., “Fixture Layout Optimization of Sheet Metals by Integrating Topology Optimization into Genetic Algorithm,” vol. 13, no.7, Article 4395, 2023. doi: 10.3390/app13074395.
A. R. Shalihah and G. Kiswanto, “Preliminary Design of 2D Ultrasonic Vibration Assisted Micro-milling (UVAMM) Using Piezoelectric Stack Actuator,” in Advances in Automation, Mechanical and Design Engineering, Cham: Springer Nature Switzerland, 2023, pp. 269–276.
M. Sohrabifard and M. Nategh, “Investigation of the stability and contact stiffness of workpiece inside fixture in different machining conditions,” Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, vol. 237, no. 20, pp. 4739–4758, 2023, doi: 10.1177/09544062231153749.
L. Ma, Z. Ma, H. Yu, S. Li, M. Pang, and Z. Wang, “Experimental Investigation of Thrust Force in the Drilling of Titanium Alloy Using Different Machining Techniques,” vol. 12, no. 11, Article 1905, 2022. doi: 10.3390/met12111905.
K. Malik, F. Ahmad, W. Keong, and E. Gunister, “The Effects of Drilling Parameters on Thrust Force, Temperature and Hole Quality of Glass Fiber Reinforced Polymer Composites,” Polymers and Polymer Composites, vol. 30, no. 6, Article 096739112211311, 2022, doi: 10.1177/09673911221131113.
Ç. Bolat et al., “Effect of Drilling Parameters and Tool Geometry on the Thrust Force and Surface Roughness of Aerospace Grade Laminate Composites,” Micromachines, vol. 14, no. 7, Article 1427, 2023. doi: 10.3390/mi14071427.
B. Tjiptady, R. Rahman, R. Meditama, and G. Widayana, “Jig and Fixture Redesign for Making Reamer on Head Cylinder,” Jurnal Pendidikan Teknik Mesin Undiksha, vol. 9, pp. 32–41, 2021, doi: 10.23887/jptm.v9i1.32597.
H. Syaifullah and F. H. Permadi, “Pembuatan Jig Proses Pre Drill Model B74 Guna Menurunkan Reject Concentric Pada Lini Produksi Pengecoran Outer Tube di PT. Kayaba Indonesia,” Technologic, vol. 12, no. 2, 2022.
I. Akmal, H. Hamdi, and D. Yuhas, “Perancangan Drilling Jig dengan Adjustable V-Block untuk Pengeboran Tangkai Drill Chuck Mesin Bor Koordinat 22 STA,” Jurnal Mekanik Terapan, vol. 3, no. 1, pp. 26–33, 2022, doi: 10.32722/jmt.v3i1.4546.
A. Efendi and R. P. Hasibuan, “Perancangan Fixture In Jig Sebagai Alat Bantu Proses Produksi Casebase di PT. Team Metal Indonesia,” Comput. Sci. Ind. Eng., vol. 6, no. 1 SE-Articles, pp. 1–10, Jan. 2022.
R. Indrawan et al., “Rancang Bangun Jig And Fixture Suction Casing Untuk Proses Milling Di Mesin Cnc Milling 3-Axis,” Jurnal Pendidikan Teknik Mesin Undiksha, vol. 10, no. 2, pp. 212–220, 2022.
R. Nanda, K. Karyadi, and M. Rizki, “Perancangan dan Pembuatan JIG FOG Lamp Mobil Dengan Material Aluminium,” Jurnal Mekanik Terapan, vol. 4, no. 1, pp. 9–14, 2023, doi: 10.32722/jmt.v4i1.5609.
M. Alqodri and G. Sirait, “Perancangan Jig Proses Drilling di PT Duo Work Engineering,” Jurnal Comasie, vol. 9, no. 5, pp. 694–702, 2023, doi: 10.33884/comasiejournal.v9i5.7803.
R. Ferdian, B. Basuki, L. D. Setyana, and A. Hendaryanto, “Perancangan Fixture Pada Proses Finishing Gerinda Tangan Sebagai Peningkatan Produktivitas Produk Spindle Knuckle D40 L di PT Manggala Perkasa Engineering,” Jurnal Mekanik Terapan, vol. 5, no. 1, pp. 25–33, 2024, doi: 10.32722/jmt.v5i1.6302.
H. Rizka, M. Matahelumual, M. T. N. Ramadhan, and G. Heryana, “Redesain Alat Pencekam Plat dalam Konteks Jig and Fixture Pada Proses Pengelasan di Meja Kerja,” Jurnal Mekanik Terapan, vol. 5, no. 2, pp. 113–120, 2024, doi: 10.32722/jmt.v5i2.6545.
S. P. Purbaningrum, A. Muttaqin, F. Sumasto, and E. S. Solih, “Perancangan Jig Machining untuk Perbaikan Electroda ST-03,” J. Serambi Eng., no. Vol. 9 No. 2 (2024): April 2024, pp. 8575–8581, 2024.
S. P. Purbaningrum, J. Johannes, F. Imansuri, D. Salati, and E. S. Solih, “Implementasi Jig Welding Untuk Meningkatkan Efisiensi Pengelasan Frame Base,” Journal of Community Services in Sustainability, vol. 2, no. 1, pp. 55–64, 2023, doi: 10.52330/jocss.v2i1.277.
H. Hibaitulah, K. Karyadi, D. Mulyadi, A. Amir, A. Supriyanto, and R. Aulia Nanda, “Optimasi Desain Jig Untuk Check Hole Pada Komponen Dudukan Shockbreaker Mobil,” Jurnal Mekanik Terapan, vol. 6, no. 3, pp. 134–142, 2025, doi: 10.32722/jmt.v6i3.7848.
S. O. Eridheni, J. N. R. Suprihartini, and Y. T. J. Wibowo, “Rancang Bangun Fixture Untuk Meningkatkan Kapasitas Produksi Proses Sprue Cutting pada Axle Bracket di PT. XYZ,” Technologic, vol. 16, no. 2, 2025, doi: 10.52453/technologic.v16i2.500.
M. Rahmi, N. A. Putri, and A. Robiyana, “Perancangan Drilling Jig Fixture untuk Flange Drum Spinner di PT. Melu Bangun Wiweka,” Jurnal Teknol. dan Rekayasa Manufaktur, vol. 8, no. 1, pp. 11–24, 2026.
D. O. Kristiawan, Y. Y. Tanoto, I. H. Siahaan, and N. Naldi, “Perancangan Adjustable Handlebar untuk Sepeda Motor dengan Dua Sistem Pengaturan,” Jurnal Teknik Mesin, vol. 18, no. 2, pp. 33–38, 2021, doi: 10.9744/jtm.18.2.33-38.
M. Simanjuntak et al., “Rancang Bangun dan Pengujian Mesin Pengering Rotari dengan Pemanas dan Penggerak Tenaga Surya pada Pengeringan Jamur Tiram,” Jurnal Teknik Mesin, vol. 20, no. 2, pp. 31–38, 2023, doi: 10.9744/jtm.20.2.31-38.
E. S. Solih, S. P. Purbaningrum, F. F. Nurhadi, D. Agustin, and W. Fauzi, Dasar Dasar Ilmu Bahan dalam Dies Stamping dan Mold. Eureka Media Aksara, 2025.
E. Solih, V. Hayoto, S. Purbaningrum, F. Sumasto, and D. Agustin, “Perancangan Hydraulic System Dalam Rangka Mendukung Dies Clamping Pada Mesin Press Seyi SN2-300 di PT Ganding Toolsindo,” Jurnal Serambi Engineering, vol. 8, no. 4, pp. 7387–7293, 2023, doi: 10.32672/jse.v8i4.6888.
E. S. Solih, V. Hayoto, and S. P. Purbaningrum, “Perancangan Hydraulic System Dalam Rangka Mendukung Dies Clamping Pada Mesin Press Seyi SN2-300 di PT Ganding Toolsindo,” Jurnal Serambi Engineering, vol. 8, no. 4, pp. 7387–7393, doi:10.32672/jse.v8i4.6888, 2023.
Downloads
Published
Issue
Section
License
Copyright (c) 2026 Adinda Rahmah Shalihah, Abdul Wahid Arohman, Fadhil Fadhlurrohman Nurhadi, Safril, Achmad Thoriq Pamungkas Sontodipoero, Albani Alif Syahputra, Al Kautsar Permana
This work is licensed under a Creative Commons Attribution 4.0 International License.
Jurnal Teknik Mesin is publihed by the Mechanical Engineering Department, Petra Christian University, Indonesia
All articles and their contents are published and distributed under the international license of Creative Commons Attribution License (CC BY).
